Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
raspberry_pi:mods [2017/07/07 09:16]
matthias [Raspberry Pi(rate)Box Mods]
raspberry_pi:mods [2017/07/07 09:40] (current)
matthias [Raspberry Pi(rate)Box Mods] added mesh howto
Line 5: Line 5:
   *[[raspberry_pi:​mods:​sfpg|Set up Single File PHP Gallery]]   *[[raspberry_pi:​mods:​sfpg|Set up Single File PHP Gallery]]
   *[[http://​blog.danielpecos.com/​2013/​09/​raspberrypi-custom-command-button/#​more-648|RaspberryPI Shutdown button via GPIO]]   *[[http://​blog.danielpecos.com/​2013/​09/​raspberrypi-custom-command-button/#​more-648|RaspberryPI Shutdown button via GPIO]]
 +  *[[laptop:​mods|PirateBox Mods]] for PirateBox itself and not RPi or one-chip specific. ​
 +  *A very hardcore plain howto to get Mesh on RPi up and running: [[raspberry_pi:​mods:​mesh|Mesh RPi]]
  
 ===== Switch used wifi adapter ===== ===== Switch used wifi adapter =====
Line 89: Line 91:
  
 **Sidenote:​** If you use multiple USB-Stick, it is strongly discouraged of using ''/​dev/​sda1''​ as a reference for mounting the devices. It may happen, that one of two devices is named sda per random. For circumventing this issue, use the device ''​UUID''​(Universally Unique Identifier) instead. [[http://​www.cyberciti.biz/​faq/​linux-finding-using-uuids-to-update-fstab/​|Follow this instructions]] for a stable setup. **Sidenote:​** If you use multiple USB-Stick, it is strongly discouraged of using ''/​dev/​sda1''​ as a reference for mounting the devices. It may happen, that one of two devices is named sda per random. For circumventing this issue, use the device ''​UUID''​(Universally Unique Identifier) instead. [[http://​www.cyberciti.biz/​faq/​linux-finding-using-uuids-to-update-fstab/​|Follow this instructions]] for a stable setup.
 +
 +===== Enable WPA for the hotspot =====
 +Change the following configuration file  ''/​opt/​piratebox/​conf/​hostapd.conf'',​ those options will enable the functionality:​
 +
 +  interface=wlan0
 +  driver=rtl871xdrv ​
 +  ssid=PrivateBox
 +  hw_mode=g
 +  channel=1
 +  ieee80211n=1
 +  wmm_enabled=0
 +  wpa=1
 +  auth_algs=1
 +  wpa_passphrase=first123
 +  wpa_key_mgmt=WPA-PSK
 +  wpa_pairwise=TKIP
 +  rsn_pairwise=CCMP
 +  macaddr_acl=0
 +
 +
 ===== PirateBox on SDCard ===== ===== PirateBox on SDCard =====
  
Line 175: Line 197:
  --- //​[[wacomalt@gmail.com|WACOMalt]] 2014/11/08 03:52//  --- //​[[wacomalt@gmail.com|WACOMalt]] 2014/11/08 03:52//
  
-===== Enable WPA for the hotspot ===== 
-Change the following configuration file  ''/​opt/​piratebox/​conf/​hostapd.conf'',​ those options will enable the functionality:​ 
- 
-  interface=wlan0 
-  driver=rtl871xdrv ​ 
-  ssid=PrivateBox 
-  hw_mode=g 
-  channel=1 
-  ieee80211n=1 
-  wmm_enabled=0 
-  wpa=1 
-  auth_algs=1 
-  wpa_passphrase=first123 
-  wpa_key_mgmt=WPA-PSK 
-  wpa_pairwise=TKIP 
-  rsn_pairwise=CCMP 
-  macaddr_acl=0