Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
raspberry_pi:mods [2017/07/07 07:16] matthias [Raspberry Pi(rate)Box Mods] |
raspberry_pi:mods [2017/07/07 07:40] (current) matthias [Raspberry Pi(rate)Box Mods] added mesh howto |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| *[[raspberry_pi:mods:sfpg|Set up Single File PHP Gallery]] | *[[raspberry_pi:mods:sfpg|Set up Single File PHP Gallery]] | ||
| *[[http://blog.danielpecos.com/2013/09/raspberrypi-custom-command-button/#more-648|RaspberryPI Shutdown button via GPIO]] | *[[http://blog.danielpecos.com/2013/09/raspberrypi-custom-command-button/#more-648|RaspberryPI Shutdown button via GPIO]] | ||
| + | *[[laptop:mods|PirateBox Mods]] for PirateBox itself and not RPi or one-chip specific. | ||
| + | *A very hardcore plain howto to get Mesh on RPi up and running: [[raspberry_pi:mods:mesh|Mesh RPi]] | ||
| ===== Switch used wifi adapter ===== | ===== Switch used wifi adapter ===== | ||
| Line 89: | Line 91: | ||
| **Sidenote:** If you use multiple USB-Stick, it is strongly discouraged of using ''/dev/sda1'' as a reference for mounting the devices. It may happen, that one of two devices is named sda per random. For circumventing this issue, use the device ''UUID''(Universally Unique Identifier) instead. [[http://www.cyberciti.biz/faq/linux-finding-using-uuids-to-update-fstab/|Follow this instructions]] for a stable setup. | **Sidenote:** If you use multiple USB-Stick, it is strongly discouraged of using ''/dev/sda1'' as a reference for mounting the devices. It may happen, that one of two devices is named sda per random. For circumventing this issue, use the device ''UUID''(Universally Unique Identifier) instead. [[http://www.cyberciti.biz/faq/linux-finding-using-uuids-to-update-fstab/|Follow this instructions]] for a stable setup. | ||
| + | |||
| + | ===== Enable WPA for the hotspot ===== | ||
| + | Change the following configuration file ''/opt/piratebox/conf/hostapd.conf'', those options will enable the functionality: | ||
| + | |||
| + | interface=wlan0 | ||
| + | driver=rtl871xdrv | ||
| + | ssid=PrivateBox | ||
| + | hw_mode=g | ||
| + | channel=1 | ||
| + | ieee80211n=1 | ||
| + | wmm_enabled=0 | ||
| + | wpa=1 | ||
| + | auth_algs=1 | ||
| + | wpa_passphrase=first123 | ||
| + | wpa_key_mgmt=WPA-PSK | ||
| + | wpa_pairwise=TKIP | ||
| + | rsn_pairwise=CCMP | ||
| + | macaddr_acl=0 | ||
| + | |||
| + | |||
| ===== PirateBox on SDCard ===== | ===== PirateBox on SDCard ===== | ||
| Line 175: | Line 197: | ||
| --- //[[wacomalt@gmail.com|WACOMalt]] 2014/11/08 03:52// | --- //[[wacomalt@gmail.com|WACOMalt]] 2014/11/08 03:52// | ||
| - | ===== Enable WPA for the hotspot ===== | ||
| - | Change the following configuration file ''/opt/piratebox/conf/hostapd.conf'', those options will enable the functionality: | ||
| - | |||
| - | interface=wlan0 | ||
| - | driver=rtl871xdrv | ||
| - | ssid=PrivateBox | ||
| - | hw_mode=g | ||
| - | channel=1 | ||
| - | ieee80211n=1 | ||
| - | wmm_enabled=0 | ||
| - | wpa=1 | ||
| - | auth_algs=1 | ||
| - | wpa_passphrase=first123 | ||
| - | wpa_key_mgmt=WPA-PSK | ||
| - | wpa_pairwise=TKIP | ||
| - | rsn_pairwise=CCMP | ||
| - | macaddr_acl=0 | ||